CLEANING EQUIPMENT
| CLEANER COMPOUND | ||
|
PART NO. | DESCRIPTION |
| 75-1000 | 4 POUND CAN OF CLEANER COMPOUND | |
| 75-1000-1 | 1 POUND CAN OF CLEANER COMPOUND | |
| NOTE: INSTRUCTIONS FOR PROPER USE ARE INCLUDED | ||
| FAUCET CLEANING ATTACHMENTS | ||
| PART NO. | DESCRIPTION | |
|
75-4352 | NICKEL PLATED CLEANING ATTACHMENT FOR USE WITH 75-901R SLIP COUPLING |
| 75-4352T | SAME AS 75-4352 BUT WITH MALE BEER THREAD ADAPTOR ON SPOUT END | |
|
75-4353 | STRAIGHT CLEANING ATTACHMENT WITH 5/16" HOSE BARB END ( 2 PIECE) |
|
75-901R | RUBBER SLIP COUPLING WITH CHAIN TO SECURE TO FAUCET. NIPPLE FOR 5/16" I.D. HOSE |
|
|
| COMPLETE KITS | |
| PART NO. | DESCRIPTION |
| 75-1842 | 1 QUART CLEANING KIT CONSISTING OF 75-1841 CLEANER, 75-905W FAUCET BRUSH, 75-904A 3/16" I.D. HOSE BRUSH, 75-4350 FAUCET COUPLING NUT WRENCH, 75-1000-1 ONE POUND CLEANING COMPOUND, DRAFT BEER FACTS BOOKLET AND INSTRUCTIONS |
| REPLACEMENT PARTS | |
| 75-1941-1N | PLASTIC JAR CAP |
| 75-1941-5 | CAP WASHER |
| 75-588P | PUMP |
| 75-752 | PUMP NIPPLE CHECK VALVE |
| 75-753 | PUMP NIPPLE WASHER |
| 75-1941-4AP | ONE QUART JAR |
| 75-1941-4BP | TWO QUART JAR |
| 75-1841-2A | CAP PLATE ASSEMBLY |
| 75-1941-8B | HOSE AND CLEANING ATTACHMENT ASSEMBLY |
| FLUSHERS | PART NO. | DESCRIPTION |
|
75-FT108 | SINGLE FLUSHER FOR SINGLE VALVE KEG VALVE TAPS |
|
75-FT110AB | DOUBLE FLUSHER FOR SINGLE VALVE KEG VALVE TAPS |
|
75-FT109S | DOUBLE FLUSHER ADAPTER. BEER THREAD ENDS PERMIT TWO SINGLE FLUSHERS TO BE COUPLED TOGETHER TO FORM A DOUBLE FLUSHER |
|
75-FT874C | CAP AND WASHER - USED ON THE MALE BEER THREAD END OF A SINGLE FLUSHER TO CONVERT IT FOR SERIES TAP CLEANING |
|
75-FT101L | ONE OZ. CAN OF PROBE LUBRICANT - AFTER CLEANING TAP, PROBES SHOULD BE LUBRICATED (SPARINGLY) WITH THIS ODORLESS, TASTELESS LUBRICANT |
| 75-FT938 | 8 OZ. TIN OF PROBE LUBRICANT | |
|
75-FT115BA | SERIES CLEANING ADAPTOR. WHEN A SERIES SYSTEM IS TO BE CLEANED BY BACK FLUSHING THROUGH FAUCET AND TAPS, THIS ADAPTOR SHOULD BE USED WITH 75-FT108 SINGLE FLUSHER AND 75-FT874C CAP TO HOLD THE PROBE CHECK VALVES IN THE OPEN POSITION |
|
75-FT85-117 | BALL LIFTER - THE INSERTION OF THIS DEVICE INTO THE BOTTOM OF THE TAP PROBE LIFTS THE BALL CHECK VALVE, PERMITTING CLEANING FROM THE FAUCET THROUGH THE TAVERN TAP |
| WRENCHES, FITTINGS | PART NO. | DESCRIPTION |
 |
75-FT872 | ELBOW FITTING FOR 75-FT86P, 75-FT86 TAPS |
| 75-FT86-12 | WRENCH, PROBE AND BEER HEX NUT | |
| 75-FT116 | WRENCH - TAP-RITE AND PERLICK PROBE |
| CLEANING BRUSHES | PART NO. | DESCRIPTION |
 |
75-904A | 3/16" I.D. HOSE BRUSH, 66" LONG |
| 75-904B | 1/4" I.D. HOSE BRUSH, 66" LONG | |
| 75-904C | 3/8" I.D. HOSE BRUSH, 66" LONG | |
| 75-904D | 1/2" I.D. HOSE BRUSH, 66" LONG | |
| 75-905W | STANDARD FAUCET BRUSH 3/4" BRISTLE X 8 3/4" LONG | |
| 75-905WL | FAUCET BRUSH 5/8" BRISTLE X 14" LONG |